Hayward Pro Logic Troubleshooting Guide How To Reset Average Salt Adjust Chlorinator Output Adjust ORP Set Points Adjust Heater Set Points Clear Inspect Cell Message Set a Pump Schedule Change VSP Speed Settings Clean the Turbo Cell Troubleshooting 1 No Cell Power Low Volts 2 Chlorinator Off High Salt Amps 3 Chlorinator Off Cell Sensor Open 4
Try it free Hayward Pool Products Pro Logic troubleshooting USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 2 Introduction The Hayward Pro Logic is a multifunction pool controller used to fully manage your pool spa sys tem The Pro Logic can control pumps valves lighting heaters and chlorination Although the Pro Logic is easy to use it is important to completely read through this operating manual before
Hayward Pro Logic Troubleshooting Guide
Hayward Pro Logic Troubleshooting Guide
https://data2.manualslib.com/first-image/i9/45/4500/449955/hayward-pro-logic-174-.jpg
Pro Logic Board Layout Diagram Cell plug Dispense power circuit output 120VAC Plugs for S D control module base antenna and CL module Plug for the local display Auxiliary relays plug top Filter Lights A1 and A2 bottom A3 A6 Four amp fuse protects actuator circuit Valves 1 4 harness plugs for actuators Heater 1 and 2
Templates are pre-designed files or files that can be utilized for numerous functions. They can conserve time and effort by offering a ready-made format and layout for creating various sort of content. Templates can be used for personal or professional projects, such as resumes, invitations, flyers, newsletters, reports, presentations, and more.
Hayward Pro Logic Troubleshooting Guide
Hayward Pro Logic Wiring Diagram
Hayward AQL2 WB RF PS 8 Black Goldline Wireless Wall Mount Remote
HAYWARD PROLOGIC TROUBLESHOOTING MANUAL Pdf Download ManuaLib
ProLogic Troubleshooting YouTube
How To Wire A 2 Speed 230V Motor To A Hayward Pro Logic System
Hayward GLX LOCAL P 4 Local Display Replacement For Hayward PL P 4
https://www.manualslib.com/manual/1619403/Hayward-Prologic.html
Page 20 Inspect Fuse Rectifier wiring Step 1C Step 1D Verify the ProLogic is receiving 120VAC between the Visually inspect test the 20Amp fuse IF fuse is blown black white wires on the Control Power side of the replace it GLX F20A 10PK IF fuse is OK inspect the terminal block Page 21 2
https://www.youtube.com/watch?v=VA509yXo0Dk
This procedure will show you how to gather diagnostic information that you can send us and also show you how to reset the average salt value if needed
https://www.manualslib.com/manual/410403/Hayward-Pro-Logic.html
Hayward Pro Logic Operation Manual Automation and chlorination Also See for Pro Logic Operation manual 52 pages Installation manual 48 pages Installation and operation manual 13 pages 1 2 Table Of Contents 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
https://hayward.com/media/akeneo_connector/asset_files/0/9/092330D_RevJ_0e4a.pdf
Www hayward Pro Logic Automation and Chlorination Installation Manual 092330D RevJ PL PS 4 PL PS 8 V PL PS 8 PL PS 16 V PL PS 16 Contents Pro Logic control configuration program desired control operation page 26 6 System Startup and checkout page 47
https://www.hayward-pool.ca/assets/documents/poolscanada/pdf/troubleshooting-guides/ProLogic-Troubleshooting-Guide.pdf
How To Pg 6 15 Reset Config to Default Reset Average Salt 7 8 Adjust Chlorinator Output Adjust ORP Set Point 9 10 Change Cell Type Clear Inspect Cell Message 11 12 Clean the Turbo Cell 13 15 Troubleshooting Pg 16 43 ProLogic vs AquaLogic SKUs 17 1 No Cell Power Low Volts 18 20 2 Blank Display 21 24 3
To use this guide determine the model number of the heat pump and the nature of the problem Refer to the Table of Contents to find the appropriate page for the problem and follow the flow charts to the solution If you have further questions Contact Hayward s Technical Service Department at 908 355 7995 Safety Detailed guide for troubleshooting the Aqua Plus and Pro Logic pool controllers Please visit https www royalswimmingpools for all your pool needs
Hayward Pool Products Pro Logic basic configuration programming